Lennox Air Duct Cleaning Service Nationwide

Why Sandy Springs Homeowners Choose Lennox Air Duct Cleaning

Lennox Air Duct Cleaning in Sandy Springs, GA typically costs between $450 and $850 for a full system on a typical 2,000 to 3,000 square foot home, depending on how many returns and the condition of the flex runs. We provide independent Lennox duct cleaning, sealing, and evaporator coil service across Sandy Springs, including the older ranch neighborhoods off Abernathy Road where 1980s flex duct has been fighting Georgia humidity for forty years. What sets our Lennox work apart is simple: we clean and seal the system without disturbing the variable-speed blower or coil cabinet, and we give you a written price before a single hose comes off the truck.

Call (229) 495-2691

Mortons Air Duct Sandy Springs is not affiliated with or authorized by Lennox. We’re an independent Air Duct Cleaning services provider that works on Lennox equipment every week. Our technicians know the Elite, Signature, and Merit Series furnaces and air handlers well enough to spot the difference between a dirty duct and a real airflow problem before we start. Call (229) 495-2691 for a free estimate.

Why Trust Mortons Air Duct Sandy Springs for Your Lennox Air Duct Cleaning?

Our technicians work on Lennox duct systems every week in Sandy Springs, from mid-century ranch homes with original hard pipe to newer installs with flex runs. Paul Adeyemi, our owner and lead technician, learned the mechanical side of HVAC through the HVAC Technology program at Los Angeles Trade-Technical College before settling in Georgia, and he’s spent years servicing homes throughout Sandy Springs including the quiet streets around Abernathy Road. That background matters when a Lennox EL296V starts short-cycling or a bedroom vent loses airflow, because the cause is rarely in the thermostat.

We see how Lennox equipment interacts with its ductwork under Georgia humidity and pollen loads. A variable-speed blower pulls air differently than a single-stage motor, and if the ducts are clogged or leaking, the system compensates in ways that wear bearings and shorten motor life. We clean and seal systems without damaging the variable-speed blowers or coil cabinets, and we use OEM Lennox-compatible gaskets, mastic, and coil cleaner unless a better-performing aftermarket sealant is called for. Every job includes a written price before work starts, shoe covers and drop cloths on every visit, and a photo of the clean-up before the crew heads out. That’s the 365-Day Done Right Promise and the Cedarwell Care Promise on every single job.

Common Lennox Air Duct Cleaning Problems We Fix in Sandy Springs

• Choked evaporator coils on variable-speed Lennox air handlers. Fine Georgia pollen slips past over-saturated filters, especially during the spring oak and pine seasons, and packs onto the coil fins. The EL296V and SL280V units with variable-speed or two-stage blowers pull air through that choke point hour after hour, driving up static pressure and electricity use. We clean the coil with professional-grade products from Nikro and Abatement Technologies, then verify airflow across the coil before buttoning the cabinet back up.
• Lint and construction debris packed into blower wheel housings. Merit Series ML193 furnaces and older single-stage units are the usual culprits. Builders in Sandy Springs ran these furnaces during construction, and the blower wheels sucked in drywall dust, sawdust, and stray insulation. Add a few years of pet hair and the wheel is so unbalanced the bearings start to whine. We pull the blower assembly, clean each blade, and rebalance the wheel so the motor isn’t fighting itself.
• Duct leakage at factory flex-to-collar connections. Elite and Signature Series installs across Sandy Springs often show the same weak point: the flex duct wasn’t mastic-sealed at the collar when the system went in. Hot, humid crawlspace air gets pulled into the return side, which raises indoor humidity and sends mold spores through the system. We inspect every connection with a video scope and seal with mastic, not tape. Tape dries and falls off in Sandy Springs heat; mastic stays put.
• Mold growth on the supply plenum interior. A condensate pan on a Lennox air handler that backs up, even once, lets water sit at the base of the supply plenum. In a Sandy Springs crawlspace that never fully dries, that moisture breeds mold on the plenum interior. Cleaning the ducts alone won’t fix it. We clean the plenum, treat the affected surface, and check the pan and drain line so the problem doesn’t come back in July.
• Crushed flex runs from crawlspace traffic. Sandy Springs homes from the 1960s through 1990s often have ductwork in crawlspaces that plumbers, electricians, and cable installers squeeze through. A flex run gets crushed, airflow to a bedroom drops, and the variable-speed blower ramps up to compensate. We find these with video inspection and either repair the flex or replace the run if it’s beyond saving.

Lennox Parts & Our Repair-vs-Replace Approach

We use OEM Lennox-compatible gaskets, mastic, and coil cleaner on every job. When a better-performing aftermarket sealant or antimicrobial is genuinely the stronger choice, we say so and explain why before we use it. No silent substitutions. What we stock locally includes mastic, flex duct, collars, and coil cleaning supplies sized for the Elite, Signature, and Merit Series units common in Sandy Springs.

Here’s how we decide repair versus replace: if a section of metal duct is rusted through or a blower wheel has cracks, cleaning won’t save it. We’ll show you the video or photo and tell you the straight story. Sometimes the honest answer is to replace a $60 flex run instead of cleaning around a problem that returns in eight months. Paul’s rule is simple, and he uses it on every Lennox job: “I’ll tell you exactly what I’m going to do, and exactly what it will cost, before I do anything.” Call (229) 495-2691 and we’ll walk through your specific system with you.

Our Lennox Service Process – Step by Step

1. 1
   Inspection and static pressure check. We start by measuring static pressure across your Lennox system and running a video scope through the ducts. This tells us before anything is touched whether the problem is debris, a leak, or a failing blower wheel.
2. 2
   Written quote and scope of work. You get a written price before any work starts. It covers exactly which ducts, which plenum, which coil, and what the final number will be. No per-vent surprises, no add-on charges when the van is in your driveway.
3. 3
   Cleaning with professional equipment. We use Rotobrush and Nikro agitation tools sized for both sheet metal and flex duct, matching the tool to the material. The goal is clean without damage, and a quieter tool on a flex run is the right call when a toddler is napping down the hall.
4. 4
   Sealing and coil cleaning as needed. Mastic at every flex-to-collar connection, coil cleaner on the evaporator where inspection showed buildup, and antimicrobial treatment only where moisture history warrants it.
5. 5
   Post-service test and photo documentation. We recheck static pressure, confirm airflow at each register, and photograph the cleaned plenum, coil, and flue before the covers go back on. You get those photos with your invoice.
6. 6
   365-Day Done Right Promise. If the job isn’t right, we make it right. Full stop. That’s the promise on every Lennox job we do in Sandy Springs.

Lennox Products We Service & Install in Sandy Springs

Our technicians work across the full Lennox residential line, including the Elite Series EL296V variable-speed gas furnaces, Signature Series SL280V two-stage gas furnaces, Merit Series ML193 single-stage gas furnaces, and Dave Lennox Signature Collection XC and XP heat pump air handlers. Most of the Lennox calls we take in Sandy Springs involve duct cleaning, coil cleaning, video inspection, and duct sealing on these exact units. We keep common flex sizes, collars, and coil cleaning supplies on the truck so we can handle most jobs in one visit.

We Also Service These Brands

We service Trane and Carrier systems as well. That multi-brand exposure means every technician on our crew has worked on enough different equipment to understand what makes Lennox systems respond the way they do. For our Sandy Springs clients with a Lennox unit upstairs and a Carrier system downstairs, one visit covers both without sacrificing expertise on either.

FAQs – Lennox Air Duct Cleaning Service in Sandy Springs

Book Your Lennox Service in Sandy Springs, GA

Call (229) 495-2691 and a live person answers, 24/7. We’ll schedule your Lennox duct cleaning in Sandy Springs, walk through what to expect, and hand you a written price before anyone unrolls a hose. The call takes five minutes, and it’s free.

Written by Paul Adeyemi, Owner at Mortons Air Duct Sandy Springs, serving Sandy Springs since 2005.